- 您现在的位置：买卖IC网 > Sheet目录17358 > LM2594APDBCKGEVB (ON Semiconductor)EVAL BOARD FOR LM2594APDBCKG
LM2594
APPLICATION INFORMATION
d + on + out
V in
t on |V out|
and d + + for a buck * boost regulator.
|V out| ) V
in
EXTERNAL COMPONENTS
Input Capacitor (C in )
The Input Capacitor Should Have a Low ESR
For stable operation of the switch mode converter a low
ESR (Equivalent Series Resistance) aluminium or solid
tantalum bypass capacitor is needed between the input pin
and the ground pin, to prevent large voltage transients from
appearing at the input. It must be located near the regulator
and use short leads. With most electrolytic capacitors, the
capacitance value decreases and the ESR increases with
lower temperatures. For reliable operation in temperatures
below ? 25 ° C larger values of the input capacitor may be
needed. Also paralleling a ceramic or solid tantalum
capacitor will increase the regulator stability at cold
temperatures.
RMS Current Rating of C in
The important parameter of the input capacitor is the RMS
current rating. Capacitors that are physically large and have
large surface area will typically have higher RMS current
ratings. For a given capacitor value, a higher voltage
electrolytic capacitor will be physically larger than a lower
voltage capacitor, and thus be able to dissipate more heat to
the surrounding air, and therefore will have a higher RMS
current rating. The consequence of operating an electrolytic
capacitor beyond the RMS current rating is a shortened
operating life. In order to assure maximum capacitor
operating lifetime, the capacitor’s RMS ripple current rating
should be:
I rms > 1.2 x d x I Load
where d is the duty cycle, for a buck regulator
t V
T
T
Output Capacitor (C out )
For low output ripple voltage and good stability, low ESR
output capacitors are recommended. An output capacitor
has two main functions: it filters the output and provides
regulator loop stability. The ESR of the output capacitor and
the peak ? to ? peak value of the inductor ripple current are the
main factors contributing to the output ripple voltage value.
Standard aluminium electrolytics could be adequate for
some applications but for quality design, low ESR types are
recommended.
An aluminium electrolytic capacitor ’s ESR value is
related to many factors such as the capacitance value, the
voltage rating, the physical size and the type of construction.
In most cases, the higher voltage electrolytic capacitors have
lower ESR value. Often capacitors with much higher
voltage ratings may be needed to provide low ESR values
that, are required for low output ripple voltage.
Feedfoward Capacitor
(Adjustable Output Voltage Version)
This capacitor adds lead compensation to the feedback
loop and increases the phase margin for better loop stability.
For C FF selection, see the design procedure section.
The Output Capacitor Requires an ESR Value
That Has an Upper and Lower Limit
As mentioned above, a low ESR value is needed for low
output ripple voltage, typically 1% to 2% of the output
voltage. But if the selected capacitor’s ESR is extremely low
(below 0.05 W ), there is a possibility of an unstable feedback
loop, resulting in oscillation at the output. This situation can
occur when a tantalum capacitor, that can have a very low
ESR, is used as the only output capacitor.
At Low Temperatures, Put in Parallel Aluminium
Electrolytic Capacitors with Tantalum Capacitors
Electrolytic capacitors are not recommended for
temperatures below ? 25 ° C. The ESR rises dramatically at
cold temperatures and typically rises 3 times at ? 25 ° C and
as much as 10 times at ? 40 ° C. Solid tantalum capacitors
have much better ESR spec at cold temperatures and are
recommended for temperatures below ? 25 ° C. They can be
also used in parallel with aluminium electrolytics. The value
of the tantalum capacitor should be about 10% or 20% of the
total capacitance. The output capacitor should have at least
50% higher RMS ripple current rating at 150 kHz than the
peak ? to ? peak inductor ripple current.
http://onsemi.com
14
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
EEM15DTBN
CONN EDGECARD 30POS R/A .156 SLD
SJP7401-5/8-50-BLACK
LOOP BLACK 5/8" X 50YD X 0.11"
EEM15DTBH
CONN EDGECARD 30POS R/A .156 SLD
RE-1515S/H
CONV DC/DC 1W 15VIN 15VOUT
GSC05DRTH-S13
CONN EDGECARD 10POS .100 EXTEND
TAAD157M016G
CAP TANT 150UF 16V 20% AXIAL
EEM15DTBD
CONN EDGECARD 30POS R/A .156 SLD
TAAD157M010G
CAP TANT 150UF 10V 20% AXIAL
相关代理商/技术参数
LM2594ASCBCKGEVB
功能描述:BOARD EVAL FOR LM2594ADJ 8-SOIC RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969
LM2594DADJG
功能描述:直流/直流开关调节器 0.5A BUCK SW REG 150KHZ RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5
LM2594DADJR2G
功能描述:直流/直流开关调节器 0.5A BUCK SW REG 150KHZ RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5
LM2594HVM-12
功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT
LM2594HVM-12/NOPB
功能描述:直流/直流开关转换器 150KHZ 0.5A STEP- DOWN VLTG REG RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT
LM2594HVM-12/NOPB
制造商:Texas Instruments 功能描述:DC/DC Converter (DC-DC) / Switching Regu
LM2594HVM-3.3
功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT
LM2594HVM-3.3/NOPB
功能描述:直流/直流开关转换器 150KHZ 0.5A STEP- DOWN VLTG REG RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT